Standards

 This standard lays down general requirements on penetrant flaw detectors and their functional units which are designed to reveal invisible, or poorly visible to the eye, surface discontinuities in metals and non-metals of any geometry and at any stage of manufacture.

This part of GYS 120 specifies an ultrasonic testing method for determining bond defects between the bearing metal and the backing.  The test can be performed on metallic multilayer plain bearings consisting of backings lined with bearing metal based on lead and tin, with layer thickness greater than or equal to 0, 5 mm.  The test is not possible within half the diameter of the crystal from the edges of the bearing, oil holes, grooves, etc. because of undefined reflections. In bearings with dovetail keying grooves at the bond, the test may not be possible along the edges of the dovetails.   

. This part of GYS 120 specifies a non-destructive penetrant testing for determining bond defects and discontinuities in the sliding surface of the bearing. The penetration method is used to detect - bond defects in the transitional area between the bearing backing/bearing material on the end faces and joint faces of multilayer plain bearings which cannot be detected by the ultrasonic testing method specified in ISO 4386- 1; discontinuities in the sliding surface of the bearing. The penetration method is applicable, in principle, to finished multilayer plain bearings.

This standard specifies requirements for full peripheral ultrasonic shear wave testing of seamless and welded tubes for pressure purposes, with the exception of submerged arc-welded (SAW) tubes, for the detection of longitudinal imperfections according to four different acceptance levels (see table 1). This standard is applicable to the inspection of tubes with an outside diameter greater than or equal to 9 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5. For tubes with an outside diameter-to-thickness ratio less than 5, one of the methods specified in Annex A shall be used by agreement between manufacturer and purchaser. 

This part of ISO 10893 specifies requirements for automated full peripheral ultrasonic shear wave (generated by conventional or phased array technique) testing of seamless and welded [except submerged arc-welded (SAW)] steel tubes, for the detection of longitudinal and/or transverse imperfections.

Unless otherwise specified in the purchase order, the testing method is applicable to the detection of predominantly longitudinal imperfections. 

In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer.

For seamless tubes, by agreement between the purchaser and manufacturer, testing principles of this part of ISO 10893 can be applied to detect imperfections having other orientations.

This part of ISO 10893 is applicable to the inspection of tubes with an outside diameter greater than or equal to 10 mm, normally with an outside diameter-to-thickness ratio greater than or equal to 5.

This part of ISO 10893 can also be applicable to the testing of circular hollow sections. 

NOTE For options for testing tubes with an outside diameter-to-thickness ratio less than 5 on longitudinal imperfections, see Annex A.

  This standard specifies requirements for eddy current testing of seamless and welded tubes for pressure purposes, with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections, according to two different acceptance levels (see tables 1 and 2).  It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm. 

This part of ISO 10893 specifies requirements for automated eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections according to the different acceptance levels as shown in Tables 1 and 2. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm.

This part of ISO 10893 can also be applicable to the testing of hollow sections. 

  This standard specifies requirements for the ultrasonic testing of the weld seam of electric resistance and induction welded steel tubes for the detection of predominantly radial longitudinal imperfections, according to two different acceptance levels.

This part of ISO 10893 specifies requirements for the automated ultrasonic shear wave (generated by conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric resistance and induction-welded (EW) steel tubes.

For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by agreement, perpendicular to the weld seam or both.

For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam. In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer.

For the detection of imperfections at the weld seam of EW tubes, full peripheral ultrasonic testing is possible. This part of ISO 10893 can also be applicable to the testing of circular hollow sections.

NOTE For full peripheral ultrasonic testing of seamless and welded (except SAW) tubes, see ISO 10893-10. 

This standard specifies requirements for the ultrasonic testing of the weld seam of submerged arc-welded (longitudinally or spirally) tubes for the detection of imperfections oriented predominantly parallel to and/or at right angles to the weld seam, according to three different acceptance levels (see table 1 and table 2).  This standard covers the inspection of tubular products with outside diameter greater than or equal to 150 mm.