Standards
This standard specifies requirements, including dimensions, materials, finish and selection for sampling for wire nails and cut nails. The following types of wire nails are covered by this standard: (a) Round plain head nails; (b) Round lost head nails; (c) Clout or slate nails; (d) Extra large head clout or felt nails; (e) Convex head roofing nails (chisel or diamond points); (f) Pipe nails (chisel point); (g) Panel pins; (h) Hardboard panel pins (round shank); (i) Hardboard panel pins (square shank); (j) Lath nails; (k) Plasterboard nails (jagged shank); (l) Oval brad head nails; (m) Oval lost head nails; (n) Tile pegs; (o) Tram nails with flat or raised head with chisel point; (p) Spring head twisted shank nails; (q) Square twisted shank flat head nails; (r) Washer head slab nails; (s) Dowels; (t) Annular ringed shank flat head nails; (u) Helical threaded shank flat head nails; and (v) Duplex head nails. The following types of cut nails are covered by this standard: (a) Cut clasp nails; and (b) Cut floor brads. The types of nail covered are illustrated in Tables 1 to 25 and in the corresponding diagrams, Figures 1 to 25.
1.2 Concrete masonry units covered by this specification are made from lightweight or normal weight aggregates, or both.
This standard specifies the ergonomic principles for the design of work systems.
This standard specifies the conditions under which ready-mixed concrete shall be made and delivered, and the methods by which the purchaser can specify with his enquiry or order, the properties of the concrete required. It provides a specification for the production and supply of ready-mixed concrete. Methods of specifying ready-mixed concrete for nominal mixes, specified strength mixes and mixes for special purposes, to meet the requirements of standard codes of practice, are covered. It also gives guidance on the data to be provided by the purchaser when ordering ready-mixed concrete, the inspection facilities to be provided by the supplier and the appropriate tests. Routine tests which must be carried out by the supplier and those which are the responsibilities of the purchaser are also included. This standard does not cover the placing, compaction, curing or protection of the concrete after delivery, nor does it apply to materials for lean concrete or similar road care materials.
These requirements cover temporary-use, seasonal decorative-lighting products and accessories with a maximum input voltage rating of 120 V to be used in accordance with the National Electrical Code, ANSI/NFPA 70. Temporary-use is considered to be a period of installation and use not exceeding 90 days. 1.2 These requirements cover factory-assembled seasonal lighting strings with push-in, midget-screw, or miniature-screw lampholders connected in series for across-the-line use or with candelabra- or intermediate-screw lampholders connected in parallel for direct-connection use. These requirements also cover factory-assembled seasonal decorative outfits such as wreaths, stars, light sculptures, crosses, candles or candle sets without lamp shades, products in the shape of, or in resemblance to, Christmas trees with simulated branches and needles, products in the shape of, or in resemblance to, wreaths provided with simulated branches and needles, blow-molded figures or objects, animated figures, tree tops, controllers, tree stands, electric tree poles, and motorized decorative displays. These requirements cover products which are portable and not permanently connected to a power source.
This standard applies to the safety aspect of toys and play things intended specifically for children.
This standard specifies the general requirements for a laboratory safety management system, which will enable a laboratory to formulate a policy and objectives. It takes into account legislative requirements and information about significant risks, that the laboratory can control and over which it can be expected to have an influence, to protect its employees and others, whose health and safety may be affected by the activities of the laboratory.
This standard specifies the general requirements for a laboratory safety management system, which will enable a laboratory to formulate a policy and objectives, taking into account legislative requirements and information about significant risks, which the laboratory can control and over which it can be expected to have an influence, to protect its employees and others, whose health and safety may be affected by the activities of the laboratory. In addition this standard specifies specific requirements for medical laboratories. This standard is applicable to any laboratory that wishes to: (a) implement, maintain and improve an Occupational Safety and Health Management System; (b) assure itself of its conformance with its stated safety policy; and (c) make s self-determination and self –declaration of conformance with this standard.