This publication:

-                      Provides technical guidance on the storage and dispensing of petroleum products including petrol, diesel, autogas (also known as LPG) and biofuels (blends of petrol or diesel containing up to 10 % biomass derived component), used as fuels for motor vehicles, primarily at filling stations to which the general public have access.

-                      Covers civil, mechanical, hydraulic and electrical installation issues for the planning, design, construction, commissioning, modification, maintenance and decommissioning of filling stations.

-                      Provides information aimed at minimizing the risks from fire and explosion, to safety, health and to the environment.

-                      Describes good practice and certain legal requirements, particularly those applicable in the UK.

-                      Is primarily intended to be applicable to both new sites and existing sites that are modified/refurbished. The guidance should also be useful in providing a benchmark to assist the duty-holder to undertake periodic review of their risk assessment(s) required under specific legislation applying to the facilities.

-                      Provides general principles that may be applicable to other types of installation where fuels are stored and dispensed for non-retail use.

This document applies to single storey houses up to 7.62 m x 12.19 m (25 ft x 40 ft) plan, with hollow block masonry or timber framed walls, and timber framed or concrete roofs.  It provides the user with the technical information to supervise the construction of a safe and durable house, and to facilitate checks on whether a safe and durable house is being built.

This document does not include construction details for utilities (including plumbing, electrical, communications, security, and natural gas.  It also does not include construction details for solid brick masonry.

1.1         This standard specifies:

(a)          requirements for the manufacturing, alloying and testing of gold articles of 23, 22, 20, 18, 15, 14, 12, 10 and 9 kt gold;

(b)         requirements for findings and solders to be used in the manufacture of gold articles;

(c)          methods for assaying gold, alloyed gold, solder, findings and gold articles;

(d)         non-destructive testing of gold articles by X-ray fluorescence spectroscopy (XRF); and

(e)          requirements for making and labelling of imported gold articles.

NOTE 1 It does not specify requirements for design of gold articles and does not apply to gold articles intended for industrial purpose such as dentistry, electronics, official coins, gold bars and other such uses.

  This standard specifies:

a a)  requirements for the manufacturing, alloying and testing of gold articles of 23, 22, 20, 18, 15, 14,12, 10 and 9 kt gold;

b b) requirements for findings and solders to be used in the manufacture of gold articles;

c c) methods for assaying gold, alloyed gold, solder, findings and gold articles; and

d d) requirements for marking and labelling of imported gold articles.

 
NNOTE It does not specify requirements for design of gold articles and does not apply to gold articles intended for industrial purposes such as dentistry, electronics, official coins, gold bars and other such uses.

This specification covers hollow and solid (see 5.3 and 5.4) concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are three classes of concrete masonry units: Normal Weight, Medium Weight, and Lightweight. These units are suitable for both load bearing and non-load bearing applications. This standard covers hollow blocks from sizes of 3in. (76.2mm) to 8 in. (203.2mm).

Concrete masonry units covered by this specification are made from lightweight or normal weight aggregates, or both.

This standard specifies the requirements and methods of test for urea, fertiliser grade.

The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

The purpose of this Standard is to provide criteria for the safe erection, use, and inspection of access scaffold (as covered in CSA S269.2 and engineered systems) and for the training of erectors and users of such equipment.

1.2 Subjects addressed

This Standard applies to the erection, use, and inspection of access scaffold that is

a) supported on a surface;

b) hung from multiple points, but is not capable of moving vertically or horizontally; or

c) mounted on wheels.

This Standard addresses key hazards, including fall hazards, structural instability, platform failures, and material handling problems.

Note: In this Standard, the term erection refers to the assembling, altering, or dismantling of a scaffold.

While this Standard applies to scaffold as defined in Clause 3, this Standard is not limited to scaffold used solely for the purpose of construction, maintenance, or repair operations.

1.3 Equipment not covered

This Standard does not apply to the following:

a) falsework and formwork for construction purposes, as covered in CSA S269.1;

b) suspended access equipment, as covered in CSA Z91 and CAN/CSA-Z271;

c) elevating work platforms, as covered in CAN/CSA-B354.6, CAN/CSA-B354.7, and CAN/CSA-B354.8;

d) manual or powered mast-climbing work platforms, such as a pump jack scaffold or equipment covered in CSA B354.9, CSA B354.10, and CSA B354.11;

e) centre-pole scaffolds; and

f) appliances or accessories attached to scaffold.

1.4 Terminology

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; may is used to express an option or that which is permissible within the limits of the standard; and can is used to express possibility or capability.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

1.5 Measurement

The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

This standard can be purchased via the Canadian Standards Association website https://www.csagroup.org/store/product/Z797-18/