This Building Code can be purchased via https://codes.iccsafe.org/content/CREEBC2018 

This standard outlines a code of safety for chemical laboratories.

1                   Scope

1.1               This standard outlines a code of safety for chemical laboratories.

1.2              The standard outlines:

(a)               general rules of conduct concerning safety;

(b)               details for fire emergency and rescue procedures;

(c)               general laboratory techniques.

1.3              This standard does not cover hazards relating to radioactive substances.

This Code of Practice specifies requirements for poultry meat which have not yet been treated in any way to ensure their preservation, except that it has been chilled or frozen and is intended for human consumption, whether by direct sale or through further processing. This Code of Practice applies to all establishments in which poultry is slaughtered, packed, or otherwise handled in the course of preparation, and all establishments in which poultry cuts and parts are processed, packed, or otherwise handled in the course of preparation. It also applies to conditions of transport from the establishment. This Code of Practice does not cover requirements for poultry rearing.

1.1         This standard specifies:

(a)          requirements for the manufacturing, alloying and testing of gold articles of 23, 22, 20, 18, 15, 14, 12, 10 and 9 kt gold;

(b)         requirements for findings and solders to be used in the manufacture of gold articles;

(c)          methods for assaying gold, alloyed gold, solder, findings and gold articles;

(d)         non-destructive testing of gold articles by X-ray fluorescence spectroscopy (XRF); and

(e)          requirements for making and labelling of imported gold articles.

NOTE 1 It does not specify requirements for design of gold articles and does not apply to gold articles intended for industrial purpose such as dentistry, electronics, official coins, gold bars and other such uses.

  This standard specifies:

a a)  requirements for the manufacturing, alloying and testing of gold articles of 23, 22, 20, 18, 15, 14,12, 10 and 9 kt gold;

b b) requirements for findings and solders to be used in the manufacture of gold articles;

c c) methods for assaying gold, alloyed gold, solder, findings and gold articles; and

d d) requirements for marking and labelling of imported gold articles.

 
NNOTE It does not specify requirements for design of gold articles and does not apply to gold articles intended for industrial purposes such as dentistry, electronics, official coins, gold bars and other such uses.

This standard establishes specification for nutrient requirements in the rations fed to poultry. It provides guidance on Good Manufacturing Practices for the production of poultry feeds and Good on Farming Feeding Practices. It applies to the production and use of all materials designed for poultry feed and feed ingredients at all levels, whether produced industrially or on farm.

This standard describes exhaust emission requirements for all new domestic and commercial vehicles which have been registered in Guyana for the first time after December 31, 1997. This standard also describes exhaust emission requirements, measurement methods and measurement equipment for all vehicles, which are imported into Guyana after December 31, 1997. All imported vehicles would be required to conform to exhaust emission limits specified in the standard. Accordingly, the exhaust emission limits must be fully documented and certified by the suppliers/manufacturers, from the country of origin.

 This standard establishes the basic principles for carrying out vibration measurement and processing data, with regard to evaluating vibration effects on buildings. The evaluations of the effects of building vibration are primarily directed at structural response, and include appropriate analytical methods where the frequency, duration and amplitude can be defined. It only deals with the measurement of structural vibration and excludes the measurement of   airborne sound pressure and other pressure fluctuations. 

This standard provides general guidance on methods of carrying out penetrant inspection on materials and components both during manufacture and in service. It does not deal with acceptance or rejection. Penetrant inspection is used to locate discontinuities, such as laps, folds, cracks, porosity and fissures, which are open to the surface of a material or component. Penetrant techniques can be used on materials irrespective of their physical properties, provided that the surface is normally non-absorbent and compatible with the penetrant process.