Standards
This publication:
- Provides technical guidance on the storage and dispensing of petroleum products including petrol, diesel, autogas (also known as LPG) and biofuels (blends of petrol or diesel containing up to 10 % biomass derived component), used as fuels for motor vehicles, primarily at filling stations to which the general public have access.
- Covers civil, mechanical, hydraulic and electrical installation issues for the planning, design, construction, commissioning, modification, maintenance and decommissioning of filling stations.
- Provides information aimed at minimizing the risks from fire and explosion, to safety, health and to the environment.
- Describes good practice and certain legal requirements, particularly those applicable in the UK.
- Is primarily intended to be applicable to both new sites and existing sites that are modified/refurbished. The guidance should also be useful in providing a benchmark to assist the duty-holder to undertake periodic review of their risk assessment(s) required under specific legislation applying to the facilities.
- Provides general principles that may be applicable to other types of installation where fuels are stored and dispensed for non-retail use.
This document applies to single storey houses up to 7.62 m x 12.19 m (25 ft x 40 ft) plan, with hollow block masonry or timber framed walls, and timber framed or concrete roofs. It provides the user with the technical information to supervise the construction of a safe and durable house, and to facilitate checks on whether a safe and durable house is being built.
This document does not include construction details for utilities (including plumbing, electrical, communications, security, and natural gas. It also does not include construction details for solid brick masonry.
This document specifies a method for the magnetic particle testing of ferro-magnetic steel and iron castings. It also gives acceptance criteria through severity levels defined by the nature, the area and the dimensions of the discontinuities present. This document is applicable to all ferro-magnetic castings, independent of the moulding method. A steel and iron casting is considered to be ferro-magnetic if the magnetic induction is greater than 1 T
(Tesla) for a magnetic field strength of 2,4 kA/m. This document only applies to those areas of the castings specified for testing, as well as the percentage
of castings to be tested
This document specifies a method for the liquid penetrant testing of steel and iron castings.
This specification covers hollow and solid (see 5.3 and 5.4) concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are three classes of concrete masonry units: Normal Weight, Medium Weight, and Lightweight. These units are suitable for both load bearing and non-load bearing applications. This standard covers hollow blocks from sizes of 3in. (76.2mm) to 8 in. (203.2mm).
Concrete masonry units covered by this specification are made from lightweight or normal weight aggregates, or both.
This document specifies the general requirements
for the competence, impartiality and consistent operation of laboratories. It is
applicable to all organizations performing laboratory activities, regardless of
the number of personnel.
Laboratory customers, regulatory authorities, organizations and schemes using peer-assessment, accreditation bodies, and others use this document in confirming or recognizing the competence of laboratories.
This standard specifies the general requirements for a laboratory safety management system, which will enable a laboratory to formulate a policy and objectives, taking into account legislative requirements and information about significant risks, which the laboratory can control and over which it can be expected to have an influence, to protect its employees and others, whose health and safety may be affected by the activities of the laboratory. In addition this standard specifies specific requirements for medical laboratories. This standard is applicable to any laboratory that wishes to: (a) implement, maintain and improve an Occupational Safety and Health Management System; (b) assure itself of its conformance with its stated safety policy; and (c) make s self-determination and self –declaration of conformance with this standard.
This standard specifies the general requirements for a laboratory safety management system, which will enable a laboratory to formulate a policy and objectives. It takes into account legislative requirements and information about significant risks, that the laboratory can control and over which it can be expected to have an influence, to protect its employees and others, whose health and safety may be affected by the activities of the laboratory.
This International Standard contains requirements for the competence of bodies performing inspection and for the impartiality and consistency of their inspection activities. It applies to inspection bodies of type A, B or C, as defined in this International Standard, and it applies to any stage of inspection.
NOTE The stages of inspection include design stage, type examination, initial inspection, in-service inspection or surveillance.
This International Standard contains requirements for the competence, consistent operation and impartiality of product, process and service certification bodies. Certification bodies operating to this International Standard need not offer all types of products, processes and services certification. Certification of products, processes and services is a third-party conformity assessment activity (see ISO/IEC 17000:2004, definition 5.5).
In this International Standard, the term “product” can be read as “process” or “service”, except in those instances where separate provisions are stated for “processes” or “services” (see Annex B).