Standards

This publication:

-                      Provides technical guidance on the storage and dispensing of petroleum products including petrol, diesel, autogas (also known as LPG) and biofuels (blends of petrol or diesel containing up to 10 % biomass derived component), used as fuels for motor vehicles, primarily at filling stations to which the general public have access.

-                      Covers civil, mechanical, hydraulic and electrical installation issues for the planning, design, construction, commissioning, modification, maintenance and decommissioning of filling stations.

-                      Provides information aimed at minimizing the risks from fire and explosion, to safety, health and to the environment.

-                      Describes good practice and certain legal requirements, particularly those applicable in the UK.

-                      Is primarily intended to be applicable to both new sites and existing sites that are modified/refurbished. The guidance should also be useful in providing a benchmark to assist the duty-holder to undertake periodic review of their risk assessment(s) required under specific legislation applying to the facilities.

-                      Provides general principles that may be applicable to other types of installation where fuels are stored and dispensed for non-retail use.

This document applies to single storey houses up to 7.62 m x 12.19 m (25 ft x 40 ft) plan, with hollow block masonry or timber framed walls, and timber framed or concrete roofs.  It provides the user with the technical information to supervise the construction of a safe and durable house, and to facilitate checks on whether a safe and durable house is being built.

This document does not include construction details for utilities (including plumbing, electrical, communications, security, and natural gas.  It also does not include construction details for solid brick masonry.

This specification covers hollow and solid (see 5.3 and 5.4) concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are three classes of concrete masonry units: Normal Weight, Medium Weight, and Lightweight. These units are suitable for both load bearing and non-load bearing applications. This standard covers hollow blocks from sizes of 3in. (76.2mm) to 8 in. (203.2mm).

Concrete masonry units covered by this specification are made from lightweight or normal weight aggregates, or both.

This document specifies the requirements for the audit and certification of a food safety management system (FSMS) complying with the requirements given in ISO 22000 (or other specified FSMS requirements). It also provides the necessary information and confidence to customers about the way certification of their suppliers has been granted.

Certification of FSMS is a third-party conformity assessment activity (as described in ISO/IEC 17000:2020, 4.3), and bodies performing this activity are third-party conformity assessment bodies.

NOTE 1 In this document, the terms “product” and “service” are used separately (in contrast with the definition of “product” given in ISO/IEC 17000).

NOTE 2 This document can be used as a criteria document for the accreditation or peer assessment of certification bodies which seek to be recognized as being competent to certify that an

FSMS complies with ISO 22000 or other sets of specified FSMS requirements. It is also intended to be used as a criteria document by regulatory authorities and industry consortia which engage in direct recognition of certification bodies to certify that an FSMS complies with ISO 22000. Some of its requirements can also be useful to other parties involved in the conformity assessment of such certification bodies, and in the conformity assessment of bodies that undertake to certify the compliance of FSMS with criteria additional to, or other than, those in ISO 22000. FSMS certification does not attest to the safety or fitness of the products of an organization within the food chain. However, an FSMS requires an organization to meet all applicable food-safety-related statutory and regulatory requirements through its management system.

NOTE 3 Certification of an FSMS according to ISO 22000 is a management system certification, not a product certification. Other FSMS users can use the concepts and requirements of this document provided that the requirements are adapted as necessary.

This International Standard describes the fundamentals of product certification and provides guidelines for understanding, developing, operating or maintaining certification schemes for products, processes and services. It is intended for use by all with an interest in product certification, and especially by certification scheme owners.

NOTE 1 In this International Standard the term “product” can also be read as “process” or “service”, except in those instances where separate provisions are stated for “processes” or “services”. Definitions of product, process and service are given in ISO/IEC 17065.

NOTE 2 The certification of products, processes and services is a third-party conformity assessment activity (see ISO/IEC 17000) carried out by product ertification bodies. The requirements for product certification bodies are specified in ISO/IEC 17065.

This document specifies chemical and labelling requirements for alcohol based hand sanitizers.

This standard applies to over-the-counter alcohol-based hand sanitizers.

This standard does not apply to:

a)              Non-alcohol based hand sanitizers;

b)              medical-grade hand sanitizers;

hand sanitizers used for surgical application

This standard specifies the minimum requirements and test methods for sodium hypochlorite solutions (liquid chlorine bleaches), including scented solutions. This standard also specifies the requirements for labelling and characteristics of containers.

This standard applies to solutions which contain sodium hypochlorite as the only active ingredient.

This standard does not apply to industrial grade sodium hypochlorite solutions.

The purpose of this Standard is to provide criteria for the safe erection, use, and inspection of access scaffold (as covered in CSA S269.2 and engineered systems) and for the training of erectors and users of such equipment.

1.2 Subjects addressed

This Standard applies to the erection, use, and inspection of access scaffold that is

a) supported on a surface;

b) hung from multiple points, but is not capable of moving vertically or horizontally; or

c) mounted on wheels.

This Standard addresses key hazards, including fall hazards, structural instability, platform failures, and material handling problems.

Note: In this Standard, the term erection refers to the assembling, altering, or dismantling of a scaffold.

While this Standard applies to scaffold as defined in Clause 3, this Standard is not limited to scaffold used solely for the purpose of construction, maintenance, or repair operations.

1.3 Equipment not covered

This Standard does not apply to the following:

a) falsework and formwork for construction purposes, as covered in CSA S269.1;

b) suspended access equipment, as covered in CSA Z91 and CAN/CSA-Z271;

c) elevating work platforms, as covered in CAN/CSA-B354.6, CAN/CSA-B354.7, and CAN/CSA-B354.8;

d) manual or powered mast-climbing work platforms, such as a pump jack scaffold or equipment covered in CSA B354.9, CSA B354.10, and CSA B354.11;

e) centre-pole scaffolds; and

f) appliances or accessories attached to scaffold.

1.4 Terminology

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; may is used to express an option or that which is permissible within the limits of the standard; and can is used to express possibility or capability.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

1.5 Measurement

The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

This standard can be purchased via the Canadian Standards Association website https://www.csagroup.org/store/product/Z797-18/